Euro Profile: Difference between revisions

From Lockwiki
Jump to navigationJump to search
(Initial page stub created with new images.)
 
(link to Plug_follower)
 
(7 intermediate revisions by 3 users not shown)
Line 6: Line 6:
|lock_type = [[Cylinder]]
|lock_type = [[Cylinder]]
}}
}}
'''European profile''' (or '''Euro profile''') is a type of [[cylinder]] design predominately used in Europe. Unlike traditional mortise and rim cylinders, the Euro profile uses a single piece of metal to connect both sides of the lock. A single [[cam]] component is placed between the two sides of the lock and is directly connected to both [[plug]]s. The Euro profile is convenient to install and replace, but it has some serious security shortcomings that must be taken into consideration. See [[#Vulnerabilities|Euro Profile (Vulnerabilities)]] for additional information.
__TOC__
== Principles of operation ==
The Euro profile has several unique characteristics when compared with other cylinder designs. In particular, many designs only allow one side to engage the [[cam]] at any given time. This allows the owner of a double sided Euro profile lock to insert a [[key]] on the inner side to engage the cam and prevent it from being opened with a key on the outer side.


==Disassembly instructions==
==Disassembly instructions==


[[File:Euro_profile_cylinder_assembled.jpg|200px|A Euo Profile cylinder mounted on a low-security indoor lock box.]]
Disassembly steps may vary slightly by design and manufacturer. The use of a [[pinning shoe]] is the preferred method for disassembling a typical double euro cylinder. Another method is to use a [[Plug_follower |segmented follower]]. The c-clips retaining both cores must first be removed and then both cores can be pulled out slightly in order to remove the center cam. One core should be rotated to approximately 4:30 or 7:30 o'clock position -- 135 degrees either clockwise or counter-clockwise -- once the cam is removed. This allows the core to be removed without driver pins entering gaps for the cam clutch. At that point, a segmented follower can be used to remove the core.
 
Locks not intended for installation and use can be disassembled in a quick but destructive procedure. The cylinder housing itself can be cut in the middle using a hacksaw or grinder. The cam will no longer be held in place and can be removed. The resulting two cut half euro cylinders can then be disassembled as outlined above.
 
== Vulnerabilities ==
 
The design of the Euro Profile cylinder leaves it vulnerable to a number of attacks. The placement of the [[cam]] in the center of the cylinder leave it especially vulnerable to [[Destructive entry|destructive]] attacks, particularly prying and pulling.
 
== Gallery ==
<div align="center"><gallery>
File:IKON WSW keyway - FXE47518.jpg | [[IKON WSW]] euro profile cylinder keyway
File:cylinder - euro profile - FXE47645.jpg | Euro profile cylinder side view
File:Euro_profile_cylinder_assembled.jpg|A Euro Profile cylinder mounted on a low-security indoor lock box.
File:FAB4xxxx_least.png‎ | [[FAB_3***/4****|FAB Profi]] euro cylinder front view
File:ABUS EC700 cut euro cylinder - FXE47684.jpg | [[ABUS EC700]] cut euro cylinder
</gallery></div>
 
== See also ==
 
* [[Cylinder]]
* [[Plug]]
* [[Lock]]
* [[Door]]
 
[[Category:Locks]]
{{Stub}}

Latest revision as of 22:03, 22 December 2022

Euro Profile

Euro profile
Euro profile cylinder.jpg
Name Euro profile
Lock Type Cylinder


European profile (or Euro profile) is a type of cylinder design predominately used in Europe. Unlike traditional mortise and rim cylinders, the Euro profile uses a single piece of metal to connect both sides of the lock. A single cam component is placed between the two sides of the lock and is directly connected to both plugs. The Euro profile is convenient to install and replace, but it has some serious security shortcomings that must be taken into consideration. See Euro Profile (Vulnerabilities) for additional information.

Principles of operation

The Euro profile has several unique characteristics when compared with other cylinder designs. In particular, many designs only allow one side to engage the cam at any given time. This allows the owner of a double sided Euro profile lock to insert a key on the inner side to engage the cam and prevent it from being opened with a key on the outer side.

Disassembly instructions

Disassembly steps may vary slightly by design and manufacturer. The use of a pinning shoe is the preferred method for disassembling a typical double euro cylinder. Another method is to use a segmented follower. The c-clips retaining both cores must first be removed and then both cores can be pulled out slightly in order to remove the center cam. One core should be rotated to approximately 4:30 or 7:30 o'clock position -- 135 degrees either clockwise or counter-clockwise -- once the cam is removed. This allows the core to be removed without driver pins entering gaps for the cam clutch. At that point, a segmented follower can be used to remove the core.

Locks not intended for installation and use can be disassembled in a quick but destructive procedure. The cylinder housing itself can be cut in the middle using a hacksaw or grinder. The cam will no longer be held in place and can be removed. The resulting two cut half euro cylinders can then be disassembled as outlined above.

Vulnerabilities

The design of the Euro Profile cylinder leaves it vulnerable to a number of attacks. The placement of the cam in the center of the cylinder leave it especially vulnerable to destructive attacks, particularly prying and pulling.

Gallery

See also

Stub lock.png
This article is a stub. You can help Lockwiki by expanding it.