ASSA d12: Difference between revisions
m (added image. Removed category:axial rotation - pin do not rotate.) |
m (spec, rating) |
||
| Line 7: | Line 7: | ||
| lock_type = [[Cylinder]] | | lock_type = [[Cylinder]] | ||
| lock_design = [[Pin_tumbler|Pin-tumbler]] | | lock_design = [[Pin_tumbler|Pin-tumbler]] | ||
| ratings = EN 1303 | |||
| related = [[ASSA 700]] | | related = [[ASSA 700]] | ||
| spec_on = true | |||
| spec_comptype = [[Pin_tumbler|Pin-tumbler]] | |||
| spec_comp = 6 | |||
}} | }} | ||
The '''d12''' is a medium security [[Pin_tumbler|pin tumbler]] made by [[ASSA]] for residential or commercial use. It is intended as a successor to the [[ASSA 700]] series which dates back to 1948. | The '''d12''' is a medium security EN 1303-rated [[Pin_tumbler|pin tumbler]] cylinder made by [[ASSA]] for residential or commercial use. It is intended as a successor to the [[ASSA 700]] series which dates back to 1948. The d12 features six pins and numerous security improvements over the original cylinder, including a paracentric keyway and patented key profiles. | ||
__TOC__ | __TOC__ | ||
| Line 81: | Line 85: | ||
{{Stub}} | {{Stub}} | ||
[[Category:Lock models]] | |||
[[Category:ASSA |d12]] | [[Category:ASSA |d12]] | ||
[[Category:Pin-tumbler locks]] | [[Category:Pin-tumbler locks]] | ||
[[Category:Paracentric keyways]] | |||
[[Category:EN 1303 locks]] | |||
Revision as of 00:02, 26 December 2022
ASSA d12
| ASSA d12 | |
 | |
| Name | ASSA d12 |
|---|---|
| Manufacturer | ASSA |
| Lock Type | Cylinder |
| Lock Design | Pin-tumbler |
| Security Rating(s) | EN 1303 |
| Specifications | |
| # of Components | 6 |
| Component Type | Pin-tumbler |
| Related Locks | |
| ASSA 700 | |
The d12 is a medium security EN 1303-rated pin tumbler cylinder made by ASSA for residential or commercial use. It is intended as a successor to the ASSA 700 series which dates back to 1948. The d12 features six pins and numerous security improvements over the original cylinder, including a paracentric keyway and patented key profiles.
Principles of operation
Add to me!
Cuts on a TrioVing d12 key.
ASSA d12 key pins and drivers.
Disassembly instructions
There are two main assemblies this lock can be found in which will vary by branding and format. One uses a C-clip on the back on the plug while the other uses a large retaining screw.
If the lock uses the retaining screw:
- Unscrew the Torx screw on the tailpiece and remove the wafer beneath it.
- Unscrew the retaining screw from the rear of the plug.
- Unscrew and remove the closing rod over the pin chambers (be careful not to allow springs to escape).
- Remove the driver pins and springs. They are all the same so there is no need to keep them in order. Key pins cannot fit through the top chambers.
- Slide the plug out of the housing.
Disassembly using a follower is possible but not recommended due to the threads on the back of the plug that accept the retaining screw.
If the lock uses a C-clip:
- Remove the C-clip.
- Insert the key and turn the plug 45-90 degrees.
- Withdraw the plug from the cylinder. (A plug follower is recommended)
Vulnerabilities
The ASSA d12 may be vulnerable to one or more of the following:
Gallery
Scandinavian profile ASSA d12 (back).
Level 1 d12 key. Bo Widén and d12 logo on right side of bow.
An ASSA d12 key profile.
An ASSA d12 keyway.
ASSA d12 plug.
ASSA d12 plug.
References
External links
- Paper by Han Fey on ASSA d12
- ASSA d12 product page (Swedish)
- Differences between ASSA 700 and ASSA d12
See also
 |
This article is a stub. You can help Lockwiki by expanding it. |
