IKON WSW - Revision history

Mgsecure: /* Gallery */

2023-02-03T12:30:58Z

Gallery: <div align="center">

← Older revision		Revision as of 12:30, 3 February 2023
Line 45:		Line 45:

	== Gallery ==		== Gallery ==
	<gallery align="center">		<div align="center"><gallery align="center">
	File:IKON_WSW_cylinder_and_key_-_FXE47530.jpg \| An IKON WSW cylinder and key, with the Bo Widén mark visible on the key bow.		File:IKON_WSW_cylinder_and_key_-_FXE47530.jpg \| An IKON WSW cylinder and key, with the Bo Widén mark visible on the key bow.
	File:IKON WSW pin-tumblers - FXE47988.jpg \| Pin-tumblers		File:IKON WSW pin-tumblers - FXE47988.jpg \| Pin-tumblers
Line 60:		Line 60:
	File:IKON WSW key blade-Reinder.png \|A view of the bitting on a WSW key.		File:IKON WSW key blade-Reinder.png \|A view of the bitting on a WSW key.
	File:IKON WSW key tip profile-Reinder.png \|WSW key tip profile.		File:IKON WSW key tip profile-Reinder.png \|WSW key tip profile.
	</gallery>		</gallery></div>

	<br clear="all">		<br clear="all">

Sandplum: corrected spelling of Widén

2023-01-17T02:03:27Z

corrected spelling of Widén

← Older revision		Revision as of 02:03, 17 January 2023
Line 24:		Line 24:
	[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]		[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]

	The WSW key is bitted on the sides and edges of the blade and is reversible. The mark of inventor Bo ~~Widen~~ appears on the key bow. The key has a row of six [[dimple]] cuts along the narrow edge of the blade, matching six pin-tumbler stacks in the cylinder. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[Plug \|plug]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].		The WSW key is bitted on the sides and edges of the blade and is reversible. The mark of inventor Bo Widén appears on the key bow. The key has a row of six [[dimple]] cuts along the narrow edge of the blade, matching six pin-tumbler stacks in the cylinder. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[Plug \|plug]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].

	The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]] sliders with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->		The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]] sliders with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->
Line 46:		Line 46:
	== Gallery ==		== Gallery ==
	<gallery align="center">		<gallery align="center">
	File:IKON_WSW_cylinder_and_key_-_FXE47530.jpg \| An IKON WSW cylinder and key.		File:IKON_WSW_cylinder_and_key_-_FXE47530.jpg \| An IKON WSW cylinder and key, with the Bo Widén mark visible on the key bow.
	File:IKON WSW pin-tumblers - FXE47988.jpg \| Pin-tumblers		File:IKON WSW pin-tumblers - FXE47988.jpg \| Pin-tumblers
	File:IKON WSW sliders - FXE47984.jpg \| Side pins		File:IKON WSW sliders - FXE47984.jpg \| Side pins

Sandplum: lift to shear

2023-01-14T18:47:07Z

lift to shear

← Older revision		Revision as of 18:47, 14 January 2023
Line 28:		Line 28:
	The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]] sliders with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->		The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]] sliders with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->

	To open the lock, all six key ~~pins and all side~~ pins must be aligned at the [[shear line]]. ''(See also [[Pin_tumbler#Principles_of_operation\|Pin-tumbler, Principles of operation]])''		To open the lock, all six key pins must be aligned at the [[shear line]] while all side pins are aligned with the sidebar. ''(See also [[Pin_tumbler#Principles_of_operation\|Pin-tumbler, Principles of operation]])''

	== Disassembly instructions ==		== Disassembly instructions ==

Sandplum: added ratings section

2023-01-14T18:04:53Z

added ratings section

← Older revision		Revision as of 18:04, 14 January 2023
Line 37:		Line 37:

	A [[Plug_follower#Pinning_shoe\|pinning shoe]], used with a modified key, is a common method for removing the plug from a Euro profile cylinder. The plug is rotated 180 degrees either clockwise or counter-clockwise, and the pin retainer inserted into the edge of the keyway. This allows the plug to be removed while preventing the driver pins and springs from escaping the cylinder housing. As an alternative method, a [[Plug follower\|segmented plug follower]] could be used.		A [[Plug_follower#Pinning_shoe\|pinning shoe]], used with a modified key, is a common method for removing the plug from a Euro profile cylinder. The plug is rotated 180 degrees either clockwise or counter-clockwise, and the pin retainer inserted into the edge of the keyway. This allows the plug to be removed while preventing the driver pins and springs from escaping the cylinder housing. As an alternative method, a [[Plug follower\|segmented plug follower]] could be used.


			== Ratings ==

			* [[EN_1303 \|EN 1303:2005]] rated 1-6-0-1-0-C-6-23

Sandplum: disassembly, spec, captions, description

2023-01-14T17:57:41Z

disassembly, spec, captions, description

← Older revision		Revision as of 17:57, 14 January 2023
Line 1:		Line 1:


	<span style="font-size:22px">{{PAGENAME}}</span>		<span style="font-size:22px">{{PAGENAME}}</span>
	----		----
Line 8:		Line 10:
	\|maker = [[IKON]]		\|maker = [[IKON]]
	\|years_produced =		\|years_produced =
			\|ratings = [[EN 1303]]
	\|patent =		\|patent =
	\|related =		\|related =
	\|spec_on = true		\|spec_on = true
	\|spec_comp = 6		\|spec_comp = 6 pin-tumblers, 5 sliders
	\|spec_comptype = [[Pin_tumbler\|Pin-tumbler]]		\|spec_comptype = [[Pin_tumbler\|Pin-tumbler]], [[Slider]]
	}}		}}
	The '''WSW''' is a [[Pin_tumbler\|~~Pin~~-tumbler]] lock made by the German company [[IKON]].		The '''WSW''' is an [[EN 1303]]-rated [[Pin_tumbler\|pin-tumbler]] lock, with a wave-track and [[Dimple \|dimple]] key, made by the German company [[IKON]].

	__TOC__		__TOC__
Line 21:		Line 24:
	[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]		[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]

	The WSW key is bitted on the sides and edges of the blade and is reversible. The mark of inventor Bo Widen appears on the key bow. The key has a row of six [[dimple]] cuts matching six pin-~~tumblers at the top of~~ the ~~keyway~~. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[Plug \|~~core~~]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].		The WSW key is bitted on the sides and edges of the blade and is reversible. The mark of inventor Bo Widen appears on the key bow. The key has a row of six [[dimple]] cuts along the narrow edge of the blade, matching six pin-tumbler stacks in the cylinder. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[Plug \|plug]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].

	The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]]s with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->		The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]] sliders with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->

	To open the lock, all six key pins and all side pins must be aligned at the [[shear line]]. ''(See also [[Pin_tumbler#Principles_of_operation\|Pin-tumbler, Principles of operation]])''		To open the lock, all six key pins and all side pins must be aligned at the [[shear line]]. ''(See also [[Pin_tumbler#Principles_of_operation\|Pin-tumbler, Principles of operation]])''
Line 29:		Line 32:
	== Disassembly instructions ==		== Disassembly instructions ==

	The WSW is disassembled in the ~~same way as~~ a ~~traditional pin~~-~~tumbler cylinder~~, ~~though extra attention must~~ be ~~paid~~ to the ~~sidebar~~ and ~~side~~ pins ~~during disassembly~~.		The IKON WSW is disassembled much like other [[Euro Profile\|euro profile]] cylinders, with some care for the sidebar and side pins during disassembly.

			The WSW has a multiple component [[Actuator \|cam piece]] that is disassembled before the plug can be removed. To access the cam components, rotate the cam until a hole in the side of the cam is revealed, and insert a tool to press the spring-biased retainer inside. At the same time, pry away the side plate of the cam. The inner two plates can then be removed, allowing the plug to slide through the cylinder housing.

			A [[Plug_follower#Pinning_shoe\|pinning shoe]], used with a modified key, is a common method for removing the plug from a Euro profile cylinder. The plug is rotated 180 degrees either clockwise or counter-clockwise, and the pin retainer inserted into the edge of the keyway. This allows the plug to be removed while preventing the driver pins and springs from escaping the cylinder housing. As an alternative method, a [[Plug follower\|segmented plug follower]] could be used.

	~~# Remove the c-clip holding the core in place~~
	~~# Insert the key and turn the [[plug]] 30-45 degrees.~~
	~~# Withdraw the plug from the cylinder, being careful to retain the sidebar and side pins.~~
	~~# (A [[plug follower]] and core shims are strongly recommended)~~

	== Gallery ==		== Gallery ==
	<gallery align="center">		<gallery align="center">
	File:IKON_WSW_cylinder_and_key_-_FXE47530.jpg \| ~~Cylinder~~ and key		File:IKON_WSW_cylinder_and_key_-_FXE47530.jpg \| An IKON WSW cylinder and key.
	File:IKON WSW pin-tumblers - FXE47988.jpg \| Pin-tumblers		File:IKON WSW pin-tumblers - FXE47988.jpg \| Pin-tumblers
	File:IKON WSW sliders - FXE47984.jpg \| Side pins		File:IKON WSW sliders - FXE47984.jpg \| Side pins
	File:IKON WSW sidebar - FXE47985.jpg \| Sidebar		File:IKON WSW sidebar - FXE47985.jpg \| Sidebar
	File:IKON WSW core top view - FXE47989.jpg \| ~~Core top~~ view		File:IKON WSW core top view - FXE47989.jpg \| An IKON WSW plug, view of the pin chambers.
	File:IKON WSW core side view - FXE47996.jpg \| ~~Core side view~~		File:IKON WSW core side view - FXE47996.jpg \| Sidebar channel.
	File:IKON WSW core bottom view - FXE47992.jpg \| ~~Core bottom~~ view		File:IKON WSW core bottom view - FXE47992.jpg \| A view of the slider chambers in a WSW plug.
	File:IKON WSW side pin - FXE47984-Edit.jpg\|Side pin		File:IKON WSW side pin - FXE47984-Edit.jpg\|Side pin

Line 70:		Line 73:
	[[Category:Dimple locks]]		[[Category:Dimple locks]]
	[[Category:Sidebar locks]]		[[Category:Sidebar locks]]
			[[Category:Slider locks]]
	[[Category:Undercut groove keyways]]		[[Category:Undercut groove keyways]]
			[[Category:EN 1303 locks]]

Sandplum: added image of key

2023-01-14T15:45:27Z

added image of key

← Older revision		Revision as of 15:45, 14 January 2023
Line 49:		Line 49:
	File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin		File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin
	File:IKON_WSW_pins-Reinder.png \|Three sizes of key pins		File:IKON_WSW_pins-Reinder.png \|Three sizes of key pins
			File:IKON_WSW_key_edge-Reinder.jpg \|A key for a WSW cylinder.
	File:IKON WSW key blade-Reinder.png \|A view of the bitting on a WSW key.		File:IKON WSW key blade-Reinder.png \|A view of the bitting on a WSW key.
	File:IKON WSW key tip profile-Reinder.png \|WSW key tip profile.		File:IKON WSW key tip profile-Reinder.png \|WSW key tip profile.

Mgsecure: add individual side pin photo

2023-01-12T14:01:10Z

add individual side pin photo

← Older revision		Revision as of 14:01, 12 January 2023
Line 45:		Line 45:
	File:IKON WSW core side view - FXE47996.jpg \| Core side view		File:IKON WSW core side view - FXE47996.jpg \| Core side view
	File:IKON WSW core bottom view - FXE47992.jpg \| Core bottom view		File:IKON WSW core bottom view - FXE47992.jpg \| Core bottom view
			File:IKON WSW side pin - FXE47984-Edit.jpg\|Side pin

	File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin		File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin

Sandplum: added category:undercut groove keyways

2023-01-03T22:50:04Z

added category:undercut groove keyways

← Older revision		Revision as of 22:50, 3 January 2023
Line 68:		Line 68:
	[[Category:Dimple locks]]		[[Category:Dimple locks]]
	[[Category:Sidebar locks]]		[[Category:Sidebar locks]]
			[[Category:Undercut groove keyways]]

Sandplum: added images, and text re Bo Widen.

2023-01-03T22:43:58Z

added images, and text re Bo Widen.

← Older revision		Revision as of 22:43, 3 January 2023
Line 21:		Line 21:
	[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]		[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]

	The WSW key is bitted on the sides and edges of the blade and is reversible. It has a row of six [[dimple]] cuts matching six pin-tumblers at the top of the keyway. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[Plug \|core]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].		The WSW key is bitted on the sides and edges of the blade and is reversible. The mark of inventor Bo Widen appears on the key bow. The key has a row of six [[dimple]] cuts matching six pin-tumblers at the top of the keyway. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[Plug \|core]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].

	The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]]s with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->		The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]]s with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->
Line 48:		Line 48:
	File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin		File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin
	File:IKON_WSW_pins-Reinder.png \|Three sizes of key pins		File:IKON_WSW_pins-Reinder.png \|Three sizes of key pins
			File:IKON WSW key blade-Reinder.png \|A view of the bitting on a WSW key.
			File:IKON WSW key tip profile-Reinder.png \|WSW key tip profile.
	</gallery>		</gallery>

Sandplum: removed from hybrid category

2022-12-31T16:24:45Z

removed from hybrid category

← Older revision		Revision as of 16:24, 31 December 2022
Line 11:		Line 11:
	\|related =		\|related =
	\|spec_on = true		\|spec_on = true
	\|spec_comp = ~~11-16~~		\|spec_comp = 6
	\|spec_comptype = [[Pin_tumbler\|Pin-tumbler]]~~, [[Side pin]]s~~		\|spec_comptype = [[Pin_tumbler\|Pin-tumbler]]
	}}		}}
	The '''WSW''' is a [[~~Hybrid lock~~\|~~hybrid~~]] lock made by the German company [[IKON]].		The '''WSW''' is a [[Pin_tumbler\|Pin-tumbler]] lock made by the German company [[IKON]].

	__TOC__		__TOC__
Line 21:		Line 21:
	[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]		[[Image:IKON WSW components full.jpg\|right\|thumb\|255px\|WSW internal components]]

	The WSW key is bitted on the sides and edges of the blade and is reversible. It has a row of six [[dimple]] cuts matching six pin-tumblers at the top of the keyway. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[core]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].		The WSW key is bitted on the sides and edges of the blade and is reversible. It has a row of six [[dimple]] cuts matching six pin-tumblers at the top of the keyway. There are three different heights for these key pins. They are T-shaped and rest in matching chambers drilled in the [[Plug \|core]]. The brass driver pins for this row of pins are a mix of three standard pins and three spool [[security pins]].

	The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]]s with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->		The WSW also features one or two [[sidebar]]s, depending on the model. The interior model has five [[side pin]]s with a single sidebar. The exterior model adds either two or five additional side pins connected to a second sidebar. The steel side pins are spring-biased and control the sidebar(s) of the lock. <!-- Each side pin has XXX cuts. -->
Line 61:		Line 61:
	{{stub}}		{{stub}}

			[[Category:Lock models]]
	[[Category:IKON]]		[[Category:IKON]]
	[[Category:Pin-tumbler locks]]		[[Category:Pin-tumbler locks]]
	[[Category:Dimple locks]]		[[Category:Dimple locks]]
	[[Category:Sidebar locks]]		[[Category:Sidebar locks]]
	~~[[Category:Hybrid locks]]~~
	~~[[Category:Lock models]]~~

← Older revision		Revision as of 15:45, 14 January 2023
Line 49:		Line 49:
	File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin		File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin
	File:IKON_WSW_pins-Reinder.png \|Three sizes of key pins		File:IKON_WSW_pins-Reinder.png \|Three sizes of key pins
			File:IKON_WSW_key_edge-Reinder.jpg \|A key for a WSW cylinder.
	File:IKON WSW key blade-Reinder.png \|A view of the bitting on a WSW key.		File:IKON WSW key blade-Reinder.png \|A view of the bitting on a WSW key.
	File:IKON WSW key tip profile-Reinder.png \|WSW key tip profile.		File:IKON WSW key tip profile-Reinder.png \|WSW key tip profile.

← Older revision		Revision as of 14:01, 12 January 2023
Line 45:		Line 45:
	File:IKON WSW core side view - FXE47996.jpg \| Core side view		File:IKON WSW core side view - FXE47996.jpg \| Core side view
	File:IKON WSW core bottom view - FXE47992.jpg \| Core bottom view		File:IKON WSW core bottom view - FXE47992.jpg \| Core bottom view
			File:IKON WSW side pin - FXE47984-Edit.jpg\|Side pin

	File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin		File:Ikon_WSW_finger_pin-Snow.jpg \| Side pin