FAB 100: Difference between revisions

From Lockwiki
Jump to navigationJump to search
(FAB 100 page created.)
 
(Added the patent.)
Line 7: Line 7:
| lock_type = [[Cylinder]]
| lock_type = [[Cylinder]]
| lock_design = [[Pin_tumbler|Pin-tumbler]]
| lock_design = [[Pin_tumbler|Pin-tumbler]]
| patent =  
| patent = CZ303220B6
| years_produced =  
| years_produced =  
| related =  
| related =  
Line 86: Line 86:
* [https://youtu.be/DMPJYwgPXrM FAB 100 - Info, pick and gut]
* [https://youtu.be/DMPJYwgPXrM FAB 100 - Info, pick and gut]
* [https://youtu.be/seJx4U0p2kw FAB 100RS - Info, pick and gut]
* [https://youtu.be/seJx4U0p2kw FAB 100RS - Info, pick and gut]
* [https://patentimages.storage.googleapis.com/27/29/36/2d92c2087176ac/CZ303220B6.pdf - patent (in Czech)]


[[Category:FAB]]
[[Category:FAB]]
[[Category:Lock models]]
[[Category:Lock models]]
[[Category:Pin-tumbler locks]]
[[Category:Pin-tumbler locks]]

Revision as of 19:52, 23 November 2021

FAB 100

FAB 100
FAB100 least.png
Name FAB 100
Manufacturer Fab
Lock Type Cylinder
Lock Design Pin-tumbler
Patent CZ303220B6


FAB 100 is a line of locks belonging to a resistance class 2 (according to CSN P EN1627:2000), which offers a basic security. It is recommended to secure garden gates, garden sheds and similar. The original FAB 100 line is now superseded by the FAB 100RS.



FAB 100

Description

The lock contains five pin stacks, with two chambers containing standard drivers, two chambers contain RBC pins and there is a single spool. This configuration hints that the manufacturer perceives dynamic methods as a higher threat than picking (although RBC pins can frustrate picking as well).

The profile used is mildly paracentric, but doesn't add much to the protection against lockpicking.

The key is blanks are freely available and key can be cut or copied without any problem.

Dissassembly instructions

To disassemble a double euro cylinder, use of a pinning shoe is the preferred method.

Other possibility is to use a segmented follower, but that requires that both cores are pulled out a bit to allow a cam removal. Then a core should be rotated to approximately 4:30 or 7:30 o'clock position (135 degrees either clockwise or anti-clockwise) to prevent driver entering a gaps for the cam clutch. Then a segmented follower can be used to remove the core.

Gallery

FAB 100RS

Description

The lock contains five pin stacks that are in the same configuration as in the previous model, but what changed is the key and the core. The FAB 100RS key doesn't have a shoulder, and its function is taken over by the notch at the nose of the key along with the RS element in the core. The RS element is a simple piece of a steel wire, inserted into a groove in the core, blocking the key from being inserted too deep into the lock.

There doesn't seem to be any security improvement the RS technology has to offer, it only prevents use of 3rd party blanks.

The profile used is mildly paracentric, but doesn't add much to the protection against lockpicking.

Dissassembly instructions

Due to the RS element presence, use of a pinning shoe is no longer an option.

Segmented follower has to be used, but that requires that both cores are pulled out a bit to allow a cam removal. Then a core should be rotated to approximately 4:30 or 7:30 o'clock position (135 degrees either clockwise or anti-clockwise) to prevent driver entering a gaps for the cam clutch. Then a segmented follower can be used to remove the core.

Gallery


Vulnerabilities

The FAB 100 is vulnerable to one or more of the following:


References


See also