EVVA MCS: Difference between revisions

From Lockwiki
Jump to navigationJump to search
Line 18: Line 18:
== Principles of operation ==
== Principles of operation ==


Main Locking Element (Magnetic Rotors)
===Main Locking Element (Magnetic Rotors)===
* There are 8 magnetic rotors, 4 on each side of the keyway [[File:Mcs_sidebar_wrong.jpg|50px]]
* There are 8 magnetic rotors, 4 on each side of the keyway [[File:Mcs_sidebar_wrong.jpg|50px]]
* Magnets in each rotor are Diametrically charged [[File:Diametric-Magnet.jpg|50px]]
* Magnets in each rotor are Diametrically charged [[File:Diametric-Magnet.jpg|50px]]
Line 27: Line 27:
* When both sidebars are slid forward the core can then rotate.  
* When both sidebars are slid forward the core can then rotate.  


Minor Locking Elements (Generation 1)
===Minor Locking Elements (Generation 1)===
* Gen 1 locks have 1 active ball bearing pin, this simply must be depressed to allow the core to turn, there is only 1 height.
* Gen 1 locks have 1 active ball bearing pin, this simply must be depressed to allow the core to turn, there is only 1 height.
* There are 12 passive ball bearings that will most often jam when an incorrect key is inserted. Occasionally these can also jam when under a picking attack, but they are less likely and need only a slight bump to be corrected.
* There are 12 passive ball bearings that will most often jam when an incorrect key is inserted. Occasionally these can also jam when under a picking attack, but they are less likely and need only a slight bump to be corrected.


Minor Locking Elements (Generation 2)
===Minor Locking Elements (Generation 2)===
* Gen 2 locks have the same active ball bearing pin, it is simply moved forward in the lock from Gen 1 [[File:Mcs_keyball_full.jpg|50px]]
* Gen 2 locks have the same active ball bearing pin, it is simply moved forward in the lock from Gen 1 [[File:Mcs_keyball_full.jpg|50px]]
* Gen 2 adds passive sliders (4 on top, 3 on bottom) [[File:Mcs_sliders.jpg|50px]]
* Gen 2 adds passive sliders (4 on top, 3 on bottom) [[File:Mcs_sliders.jpg|50px]]

Revision as of 17:02, 31 July 2019

EVVA MCS

EVVA MCS
Mcs cylinder.jpg
Name EVVA MCS
Manufacturer EVVA
Lock Type Cylinder
Lock Design Magnetic
Year(s) Produced 1975-Present
Patent US 4,084,416


The MCS (or Magnetic Code System) is a magnetic lock made by EVVA. It is one of the few magnetic locks to gain widespread acceptance and is also considered one of the best mechanical locks in the world. The MCS has been sold under a variety of names, including IKON System M (DE) and Mottura MC (IT)[1].


Principles of operation

Main Locking Element (Magnetic Rotors)

  • There are 8 magnetic rotors, 4 on each side of the keyway Mcs sidebar wrong.jpg
  • Magnets in each rotor are Diametrically charged Diametric-Magnet.jpg
  • A plate with one or more gates is glued to the magnet Mcs magnet rotors.jpg
  • Inner sidebar has 3 fingers and outer sidebar has 1 finger/pin that interact with the rotor gates Mcs plate hooks.jpg
  • Whole sidebar must slide fore (towards key bow) Mcs sidebar open.jpg
  • To align with milling in the bible Mcs cylinder boring.jpg
  • When both sidebars are slid forward the core can then rotate.

Minor Locking Elements (Generation 1)

  • Gen 1 locks have 1 active ball bearing pin, this simply must be depressed to allow the core to turn, there is only 1 height.
  • There are 12 passive ball bearings that will most often jam when an incorrect key is inserted. Occasionally these can also jam when under a picking attack, but they are less likely and need only a slight bump to be corrected.

Minor Locking Elements (Generation 2)

  • Gen 2 locks have the same active ball bearing pin, it is simply moved forward in the lock from Gen 1 Mcs keyball full.jpg
  • Gen 2 adds passive sliders (4 on top, 3 on bottom) Mcs sliders.jpg
  • Key has slider tracks on the top and bottom Mcs profiles.jpg
  • If sliders are incorrect they will jam the core not allowing magnetic sidebar to be tested. Mcs sliders partial.jpg
  • Once aligned core will rotate (until sidebar comes into play). Mcs sliders full.jpg
  • WARNING! Sliders can fall out of place once core is rotated if lock is more worn and a key is not in the lock.





Disassembly instructions

Generation 1 (1 active ball bearing, 12 passive ball bearings)

  1. Remove c-clip
  2. Depress active ball bearing with a tool and slide core towards front
  3. Keep checking both ball bearing and gap towards the rear of plug as they will both get caught on the 3 passive pins and 1 active pin as plug moves forward
  4. Once plug is out:
    1. Remove split ring sidebar reset system
    2. Remove outer sidebar
    3. Use pliers or knife to snap out plastic sidebar spacer (WARNING! older locks the plastic can be quite brittle, likely it will crack, though cracked sidebar spacers can be repaired with superglue)
    4. Remove inner sidebar to then access the rotors
    5. Rotors can be removed
    6. Repeat for other sidebar

Vulnerabilities

The MCS is considered one of the best mechanical locks in the world.

Confirmed picking and decoding are possible on this lock using an audio attack for feedback.

It is vulnerable to one or more of the following:

Gallery

References

  1. PULFORD, Graham (2007). High Security Mechanical Locks: An Encyclopedic Reference. ISBN 0750684372.

See also

Stub lock.png
This article is a stub. You can help Lockwiki by expanding it.